Wednesday, March 5, 2014

Kiss Me- PTU


:: What You’ll Need ::

I've used the lovely PTU artwork called 2013MyHeart by Ismael Rac.
This is a PTU kit called Kiss Me by Digital Indulgence. Get it at PMTw/S.
Template001 (Lovely) by Me, at PolkaDot Scraps.
The mask is WSL_Mask362, by Wee Scott Lass. It’s the last one in this post.
Font used is Send Flowers.


:: Let’s Begin ::

Open the Lovely Template001, either the PSPIMAGE or PSD layered ones.
Delete the Copyright layer.
Go to Image>Resize and type in 600 pixels for the width to resize.
Go to Image>Canvas Size and resize it 800x800 from the center.

Open Paper12 from the kit.
Copy your paper and go to the template.
On the layer named square, go to
Selections>Select All, Selections>Float, Selections>Defloat.
Go to Layers>New Raster Layer (hit ok)
Paste your paper into this selection by going to Edit>Paste Into Selection (or right clicking and click Paste>Paste Into Selection).
Turn off your selection by going to Selection>Select None.
Be sure to delete the original square layer from your template.
(Do this with every layer you add a paper to.)

Open Paper14 from the kit.
Copy your paper paste it to the circle by going to
Selections>Select All, Selections>Float, Selections>Defloat.
Paste your paper by going to Edit>Paste As New Layer (or right clicking and click Paste>Paste As New Layer).
Then go to Selections>Invert and press the Delete button on your keyboard to delete the extra paper.
Selections>Select None

Use this same process to add the following papers to the layers named.
Paper3 to layers named left top circle & right bottom circle.
Paper13 to layer named rectangle.
Paper15 to layers named left circle and right circle.

Add Paper6 to layer to the oval with the “Paste Into Selection” process above.

Open element named Heart from kit.
Copy and Paste as a new layer above the two heart layers in the template.
Resize and cover the original hearts, replacing them and deleting the layers.

Copy and Paste your tube as a new layer above your circle layer.
Resize the tube as needed and center over the template.
If using the same tube as me, line up the bottom of the tube with the bottom of the square paper layer.

Open Wired Words1 from kit.
Copy and Paste it as a new layer above the top layer.
Resize and arrange it at the bottom of the tag as shown.

Open Charm2 from kit.
Copy and Paste it as a new layer above the wired word.
Resize and rotate it to the left a little and arrange it at the bottom of the O.

Open Heart Candy from kit.
Copy and Paste it as a new layer above the square layer.
Resize and arrange it the bottom right above that circle layer.
Layer>Duplicate (or right click and hit Duplicate)
Arrange this one above the top left circle and rotate it a little to the right to show more.

Open Ribbon Flower from kit.
Copy and Paste it as a new layer above the circle layer.
Resize and arrange it to the bottom left as shown.

Open Button3 from kit.
Copy and Paste it as a new layer.
Resize and arrange it to the left as shown.

Open Flower Button from kit.
Copy and Paste it as a new layer.
Resize and arrange it to the bottom left as shown.

Open Ribbon Flower from kit again.
Copy and Paste it as a new layer above the tube layer.
Resize and arrange it to the bottom right of the tube as shown.

Open Winged Heart from kit.
Copy and Paste it as a new layer.
Resize and arrange it to the bottom of the tube as shown.

Open Boarder2 from kit.
Copy and Paste it as a new layer.
Resize and arrange it to the bottom as shown.

Open Bead1 from kit.
Copy and Paste it as a new layer.
Resize and arrange it to the bottom as shown.

Add noise to all the white mat layers by clicking each layer and going to
Adjust>Add/Remove Noise>Add Noise
Check Uniform and Monochrome
Set noise to 50%

Open Paper3 from kit.
Copy and Paste it at the bottom layer of the tag.
Add your mask by going to Layer>Load/ Save Mask>Load Mask from Disk.
Apply the mask named WSL_Mask362.
Merge the mask group by right clicking the layer of the finished mask, go to Merge>Merge Group.
Resize and arrange it to fit as shown.

I like to crop and resize here before adding my text!

I used the font Send Flowers. Set it to a size you like and a stroke width of 4.
Foreground color to white and background color to #f42c88.
Duplicate the layer and select the second font layer with the font tool.
Set the stroke width to 0.
Merge the 2 font layer and convert to a raster layer.

Drop shadow everything except the mask.
Effects>3D Effects>Drop Shadow, set the drop to 3 vertical, 2 horizontal, 75 opacity, 4 blur.

Add your copyright info and your tagged by stuff.

Merge everything in Layers>Merge>Merge Visible


All Finished!

No comments:

Post a Comment